Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Blog Article
What are your insights and beliefs on How to Install a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can move easily; if you need to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. Make certain you have certified yourself for the task and fit attempting it. As opposed to hiring a specialist to take over a halfway-completed task, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you mount a brand-new bathtub in your washroom if you have currently acquired a new bathtub and don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making certain that the washing machines remain in area in between the tap as well as the sink. Secure the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bathtub has actually been used a minimum of once as this will certainly resolve it into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, causing the water to permeate the wall between the bath as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can fracture rather early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our article on Installing A Bathtub. Many thanks for finding the time to browse our article. Enjoyed reading our content? Please share it. Help another person find it. Many thanks for your time. Don't hesitate to come by our site back soon.
Schedule A Free Estimate
Report this page